Dolphin Pro 2 T top is designed for the mid to large size centre console fishing boat. Will fit consoles up to 47 inches wide.
With a great blend of curves and weight this T Top will blend with any boat on the market. Dolphin T Top is built with strong aluminum tube, the canopy is made from VIII grade UV resist Acrylic. Our unique design of the canopy with zipper make the installation very easy and customer looking, there is no time wasted with annoying bungee cord, weaving in out of holes. Center Console Alloy or fibreglass 18ft to 25ft Attaches direct to your floor.
4 x standoffs lock into console. Removable cover, zipper and velcro. 2 inch heavy duty frame Large grab handle Quick release for storage. 83 inches high Up to 47 inch wide consoles 82 inches long x 61 inches wide Cover 28 inches front to rear feet center to center. Front leg loosen the middle bolt.
Remove the top and bottom bolt from the joint Remove the bolt from the rear leg. Pivot the T Top forwards. If needed you can remove bolt from top frame joint See picture in gallery.
2 inch heavy duty anodised 6063 alloy frame. CNC Machined 6061 Alloy fitting. Marine grade VIII, UV resist cover. EXPLODED VIEW OF THE DOLPHIN PRO T TOP FOR REFERENCE. STEP 1: Unpack and check the contents of the box and check parts list.Please Read all Instrustion prior to installation If you are NOT sure of any part of the guide or you have any questions Please contact the supplier or DOLPHIN T Tops. STEP 2: Positioning of the lower half of the side frame. Distance from the centre console to lower side frame (1inch to 7inch) Check under the floor for wires or other objects that could effect the mounting Place the lower half of side frame in the desired postion and mark as a reference Remove the side frames and Measure the distance between the front mounting position from Port to Starboard (side to side) Right this measurement down. STEP 3: Assemble the side support frame Attach the lower half and upper half of the side frames using the bolts and split washers. Note the Dolphin logo faces outwards from the boat Note the bolt heads will be consealed in the counter sunk area and face inwards towards the console.
Note you have a Port and Starboard Side Frame as described above logos facing outwards. STEP 4: Attach the ball clamps to top of Side Frames The top of the side frame has a counter sunk circle with a threaded hole, the ball clamps have a raised circle area. Insert the raised circle area into the counter sunk hole of the side frame insert bolt from inside the ball clamp into the side frame end and tighten. NOTE Allow the ball clamp to rotate very slightly for adjustment. STEP 5: Assember the front and centre section of the top frame Note the shape of the front section is narrow and also has a bend curve which faces downwards when attached to the side support frames of the T Top.
Note the lap joints have a number on the! At face match these up for correct installation. STEP 6: Attach the Side Supports to the Assemble Top Section Check the direction of the side support arms Logo to the outside, handle to the rear The small curved top frame for the cover curves and bends downwards to the floor Remove the tops of the ball clamps please NOTE the clamps are to be placed on the same way (they are numbered inside) Find the centre of the cross bar on the top section mark this.Use the measurement you marked out for the postion of the deck mounts Mark this in the two cross beams on the top section that is assembled. Attach the partial top section to the support frame ensuring all parts are facing the correct direction. Refer to pictures of T Tops for reference if unsure. STEP 7: Attach the T top to the floor of the boat Place the T Top you have assemble on the marks you have made near your console Now you can pre drill and use the bolts and backing plates and lock in you mounting points NOTE: Check under the! Oor for any wires or objects before drilling holes.
STEP 8: Attach rear section of the top frame to the T Top. STEP 9: Attaching the cover to the top frame. Remove the cover and lay out on the ground. Note: there is a zipped front pocket which is zippered from side to side.
Place this over the front section of the T top and zipper up now you can fold out over the rest of the top frame and hook over the back and zipper this section up and the velcro corner sections. Now you can pull tight the side section with zippers and velcro tabs. S to T Top side main frames.CARE AND MAINTENANCE Be sure to check and tighten all fastners and connections prior to every use Be cautious when towing or driving under obstacles, low hanging structures or trees Leave dolphin t top in the erect position when towing behind a vehicle Use soap and water to clean your tower. Avoid abraisive material that might scratch or damage the tower protective!
Always rinse and wipe down tower after contact with salt (brackish) water. To claim you must contact Dolphin T Tops or is Distributor. The product/part is to be sent to the Distributor for inspection where it will either be repaired or replaced. Dolphin is not responsible for personal injury or damage to the boat caused by the use of the t top or any transport charges or cost of installation or removal of the t top.Dolphin is not liablity for direct or indirect or consequential damages resulting from delay or improper installation. Cally excluded as their care and use can not be controlled by Dolphin. WARNING The construction of your boat, design, thickness of ooring deck and walls and overall design may cause movement at the mounting points. If in doubt do not install the t top Check all bolts and parts prior to use, especially after towing behind a vehicle, lowering and raising after storage. WARNING Do not stand, climb or jump o# tower, do not tow the boat behind a vehicle with the t top lowered. Do Not Ski, wake, tow tubes, boats or other watercraft from the tower. Watch out whilst moving under objects, such as bridges, low building and trees. The item "Dolphin Pro2 T-TOP/ Center Console Boat T TOP Customized Looking Heavy Duty" is in sale since Thursday, September 17, 2020. This item is in the category "eBay Motors\Parts & Accessories\Boat Parts\Accessories & Gear\Covers". The seller is "make_a_wake_marine" and is located in Azusa, California. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Panama, Jamaica, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay.